Top Brands
Brands You Follow
You Visited
You Follow
You Search For
Hottests Topics
Featured Catalogs
People Like You
Your apps
Discover apps
Get Advice
Top Questions
Your Q&A
Friends Asked
Ask A Question | Show All Questions
More on ShopYourWay

Answers for "frigidaire dryer problem "

Showing 25,119 questions in frigidaire dryer problem
Appliances (2,681)
Tools (173)
Automotive (61)
Computers (14)
See All
Kenmore (15,183)
Frigidaire (1,436)
Whirlpool (1,087)
Maytag (796)
Craftsman (637)
LG (492)
Samsung (192)
See All
Want to know something? Ask a question
Manage My Life
frigidaire dryer problem
by Manage My Life 
August 22nd, 2011
Joey S
Thank you for your question and I understand your concern.

Your control panel is in a control lock out mode.

To remove the control lock, press Options and Select.

To avoid having someone accidentally start or stop the dryer, press Options and Select at the same time and hold for 10 seconds. "LOC" will be displayed.

I added an image below with the instructions as shown in the Operating Instructions.

This may be the issue. If not, please reply and I will be glad to assist you further.
by Joey S
August 24th, 2011
| Be the first to comment
Manage My Life
Frigidaire dryer
by Manage My Life 
January 13th, 2012
Fred M
Thank you for the reply. Unfortunately the noise from the washer is not so easily handled. The problem is still a bearing but the repair is a little more complicated. The transmission must be removed to access the bearing. On a scale of 1 (easy) to 1 (difficult) this would be a 10. The image below shows how to remove thefront panel. This may give you a better idea where the noise is comming from.
by Fred M
July 23rd, 2013
| Be the first to comment
Briana Peterson
Frigidaire Dryer
by Briana Peterson 
October 7th, 2010
Manage My Life
It sounds like your describing the front drum bearing or the drum glides. On something like this we will need a model number in order to identify what part you're talking about. I am sending you the most common model of Frigidaire dryer front drum bearing replacement instructions. If this is not your model please reply back with a valid model number for further assistance.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website:

Sears Home Services


SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.
Answered in 19 hours
by Manage My Life
October 8th, 2010
| Be the first to comment
Manage My Life
frigidaire plhs67eesb9 icemaker problem
by Manage My Life 
March 13th, 2012
scott d
Nathan, the water valve should solve this problem. It does supply both the icemaker and the water dispenser. It's a large assembly that actually has 3 separate valves and solenoids, so the icemaker and dispenser work independently. I'm attaching some images of the valve below. I hope this will help you.
Answered in 13 hours
by scott d
March 14th, 2012
| Be the first to comment
Manage My Life
frigidaire upright freezer problem
by Manage My Life 
July 7th, 2011
Fred M
One thing to listen for is a click when the unit is first turned on. If the compressor tries to start but "click" off on the overload then at least we can assume there is voltage to the compressor start relay.

This might mean the problem is with the compressor or start relay/overload.

No click and no voltage might indicate a problem with the control thermostat or even a defrost timer if there is one.

I suggest the first thing to check is voltage to the compressor. I might be able to be more specific if you can provide a model number.

Please reply with a model number for further assistance.
by Fred M
July 9th, 2011
| Be the first to comment
Manage My Life
Kenmore (Frigidaire) Electric Dryer ModNo. 417.84152500 throwing error codes 95 and 56. Symptom; not heating. What is causing this problem?
by Manage My Life 
July 24th, 2010
Manage My Life
Thanks, Dave.. Solved the problem. The L2 at the buss connection was corroded. Consequently, voltage under dropped. I installed a new 30 amp breaker pair into an open panel slot to support the dryer load and that put it right.
by Manage My Life
July 27th, 2010
| Be the first to comment
Steve Carman
Power Problem with Frigidaire Model GLD2160scs0
by Steve Carman 
February 19th, 2013
Steve Carman

Thanks very much. I really appreciate that detailed info. I've ordered the control board and will check it out next week. I had checked the leads going into the transformer on the drain pump for continuity and got about 25 ohms I think in that. That seemed ok. I also checked the leads to ground but am not positive about what came out of that. I'm going to recheck that at your direction before trying to install the control board.

As for the control board itself, I did measure 120V AC into the board from the main wires and then some minor outputs, something like .34V DC between some of the pins on the ribbon connector into the LED pushbutton unit. I have no idea what was supposed to come out of those but there is SOME power, albeit small amounts.

Thanks again. That was a great answer. I really appreciate your time!
by Steve Carman
February 21st, 2013
| Be the first to comment
frigidaire refrigerator problem with ice dispenser
July 8th, 2012
Bill W
Thank you for your question. It is concerning when a major appliance is giving trouble. The thing to do now is the check the 120 Volts AC and the Volts DC to the display on the dispenser housing. For me to give you the correct pins needing to be checked I will need the full model number.

If you have a multimeter and feel confident about doing the checks, we will get the problem solved.
by Bill W
July 11th, 2012
| Be the first to comment
Manage My Life
Frigidaire dryer will not heat LEQ1452KS0 Frigidaire Dryer
by Manage My Life 
January 14th, 2013
Manage My Life
I can understand how important it is to have your dryer working properly. Electric dryer runs but does not heat, due to a tripped breaker or blown fuse. Electric dryers require two 30 amp breakers or fuses in the house electrical box to run and heat. If one breaker is tripped or one fuse is blown, the motor, the timer and lights can work but the dryer will not heat.


Before you start verify that the dryer was not set on the Air Dry setting. Dryers will not produce heat on this setting.

Locate two 30 amp breakers and turn them off by moving the switch to the off position.

Wait at least 30 seconds and turn the circuit breaker back on by moving it to the on position.

Select a heating cycle and put some clothes inside the dryer.

Run the dryer for about a minute

Open the dryer door and touch the clothes to see if the dryer is heating again.

If the circuit breaker box contains fuses check for any fuses that may be blown and replace them with comparable fuses. If you are still having the same problem, then the images below will help. These will show you where and how access the thermal fuse and the thermostats. Before replacing any parts I would suggest that you test them. I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.
by Manage My Life
January 15th, 2013
| Be the first to comment
Manage My Life
Frigidaire clothes dryer GSEQ642AS2 Frigidaire Dryer
by Manage My Life 
May 29th, 2013
Joey S
Thank you for your question and I understand your concern.

If the heating element is heating, the element is likely okay. The most common reason for a dryer to take too long to dry is a restricted venting system or a restriction down inside the lint filter housing. 

Check the vent hose and vent system for any kinks or restrictions. Check the outside vent hood too and make sure the flapper door is opening and not stuck shut.

For testing purposes only, disconnect the vent hose from the back of the dryer and then dry a normal load. If it dries in a normal amount of time, the vent system is likely restricted.

Check the things I have covered here and if I may be of further assistance as more details become available, please reply to this post.
by Joey S
June 1st, 2013
| Be the first to comment