Answers for "kenmore electric range f3 "

Showing 74,844 questions in: kenmore electric range f3
Answers
Category
Appliances (35,253)
Tools (279)
Clothing (21)
See All
Brands
Kenmore (69,328)
Whirlpool (583)
Craftsman (488)
Frigidaire (292)
Maytag (290)
LG (168)
See All
Tags
Ask a question Did you know? There are over 1,000 experts on Shop Your Way waiting to answer your question!
Manage My Life
F3 on electric range
by Manage My Life 
December 27th, 2012
Manage My Life
With the error on your range can be frustrating as well a concern. I have done some research on the Manage My Life website and have located a link similar to your issue. While you are waiting for a detailed reply from an expert I have provided the link below. Hope this helps!
Answered in 7 minutes
by Manage My Life |
December 27th, 2012
| Comments
Manage My Life
What does F3 mean on a Kenmore electric range model number 790.95682301?
by Manage My Life 
May 16th, 2009
Lyle W
The F3 indicates that the electronic oven control board senses an "open" or "short" oven temperature sensor probe circuit. This can be caused by a failed oven temperature sensor, a wiring failure or a defective electronic control board. I recommend

unplugging the range

and checking the resistance through the sensor circuit. The temperature probe is connected to the electronic oven control board through the violet wires on pins 12 and 13 of the P5 plug as shown in the first image below. Unplug this connector (with the range unplugged) and measure the resistance through the violet wires with a volt/ohm meter. The normal resistance of this circuit is shown in the second image below. The circuit should measure about 1100 ohms at room temperature. It will likely measure near zero ohms (short) or infinite resistance (open). If it measures the normal resistance, the electronic board will need to be replaced. If the circuit measures open or short, the resistance will need to be checked directly at the temperature sensor probe. If the probe is bad, it will need to be replaced. If the probe is okay, then the wiring harness will need to be replaced.

You can order parts from the

Sears PartsDirect

website.

If you are not completely confident in your technical ability to safely access and check these components, I recommend calling a service technician to repair the range.
by Lyle W |
May 19th, 2009
| Comments
Manage My Life
What does an F3 error on my Kenmore electric range mean?
by Manage My Life 
April 9th, 2009
Fred M
Without a model number I can't be specific but an F3 error most likely means the oven has a shorted oven temperature probe.

If you submit another question with a model number I may be able to assist you in checking this yourself if you have access to a volt/ohm meter.
by Fred M |
April 15th, 2009
| Comments
JEFF SCOTT
What does the F3 error mean on my Kenmore electric range?
by JEFF SCOTT 
January 22nd, 2010
Manage My Life
This is an issue you can fix yourself. The F3 indicates the oven sensor is bad. You can test the oven sensor. Begin by disconnecting the power to the range and removing the rear panel covering the ERC. Remove the back panel from the range and follow the oven sensor wires up to the control. Disconnect the plug on the ERC containing the oven sensor wires and read the resistance of the oven sensor. It should read between 1000-1200 ohms.

If the oven sensor tests within this range the ERC is defective. If it tests out of the range disconnect the wires from the oven sensor and measure the resistance of the oven sensor. If it tests out of the range the oven sensor is defective. If it tests within the range the harness between the ERC and the oven sensor is defective.

Always unplug or de-energize electrical equipment before removing covers or attempting service

. The oven temperature sensor is located in the oven cavity in the upper left rear corner or the rear upper right corner. The oven temperature sensor probe can be removed and disconnected from inside the oven cavity and tested with an Ohm meter. Pull the sensor into the oven approximately 10 inches for access to the quick disconnect. The oven sensor should have a resistance measurement of approximately 1100 ohms at room temperature. If the oven sensor does not have approximate resistance of 1100 ohms, replace the

sensor

; click here

Sears Parts Direct

If the sensor ohms at approximately 1100 ohms then you will need to reconnect it and then make the same test up at the control board by disconnecting the sensor harness plug and rechecking the resistance across the two sensor wire leads. If it measures approximately 1100 ohms there, replace the

control board

click here;

Sears Parts Direct



If you require further assistance please resubmit question with details of the checks you have made. I will be looking forward to helping you again in the near future.
Answered in 7 hours
by Manage My Life |
January 22nd, 2010
| Comments
Manage My Life
What is an E3 F3 error code in my Kenmore electric range?
by Manage My Life 
February 8th, 2010
Manage My Life
The F3 E3 means the EOC (Electronic Oven Control) senses an over temperature condition. The tech sheet advises us to check the oven temperature sensor resistance (See images below). Begin by disconnecting the power to the range and removing the rear panel covering the EOC. Remove the lower panel from the range and follow the oven sensor wires up to the control. Disconnect the plug on the EOC containing the oven sensor wires and read the resistance of the oven sensor. It should read between 1000-1200 ohms.

If the oven sensor tests within this range the ERC is defective. If it tests out of the range disconnect the wires from the oven sensor and measure the resistance of the oven sensor. If it tests out of the range the oven sensor is defective. If it tests within the range the harness between the ERC and the oven sensor is defective.

If you require further assistance please resubmit question with details of the checks you have made. I will be looking forward to helping you again in the near future.
by Manage My Life |
February 11th, 2010
| Comments
Manage My Life
What could cause F3 to appear on the display of my Kenmore electric range?
by Manage My Life 
January 25th, 2008
Manage My Life
I have a Kenmore electric range, serial #2R248138Q, Model #911.9352590.

The question below answers your question. The model number is different, but the diagnosis is the same. The resistance of the oven temperature sensor should be around 1100 ohms at 70 degrees. The resistance increases as temperature increases. If the reading is within 100 ohms of 1100, the sensor is good.
Answered in 0 seconds
by Manage My Life |
January 25th, 2008
| Comments
Manage My Life
F3 91145565690 Kenmore 30" electric drop-in range
by Manage My Life 
June 22nd, 2013
Manage My Life
Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner.

 

Thank you for using Searspartsdirect.com!
Answered in 2 minutes
by Manage My Life |
June 22nd, 2013
| Comments
Manage My Life
kenmore range f3 code
by Manage My Life 
August 29th, 2013
Ron  Hawkins
Thanks for contacting mange my life about your range/oven model 911.46555691; sorry you are having a problem with this, I will be glad to assist you.

Based on your testing of the sensor and related wiring I would agree that the control should be replaced.

Electronic Control

I do see that the original control is not available and has been substituted. I also see that this replacement can only be ordered by a technician. You would have to discuss with the parts department for details.

Here is a link to

Sears Parts Direct

.

 

Ron H.

 

 
Answered in 21 hours
by Ron Hawkins |
August 30th, 2013
| Comments
Manage My Life
F3 error code JSP38GT1BB Ge Electric range
by Manage My Life 
January 26th, 2013
Joseph Perez
Error codes can be an inconvenience and keep your range from working properly. I did some research and I was able to find a link that will provide you with some good information. I hope this helps with your research while you wait for your expert response.
Answered in 10 minutes
by Joseph Perez |
January 26th, 2013
| Comments
Ethan Jarrell
9117398710 Kenmore Range - F3 Error
by Ethan Jarrell 
May 21st, 2012
Joseph Perez
Error codes can be an inconvenience and I will be happy to help. I did some research and I was able to find a link that will provide you with some good information. I hope this helps while you wait for your expert response.
Answered in 5 minutes
by Joseph Perez |
May 21st, 2012
| Comments